|
SLD模塊對驅動電流/電壓非常敏感，在驅動電路設計上的任何錯誤都可能導致SLD模塊的損壞或失敗。在大多數情況下，模塊是不能由這種損壞而修理的。為了提供一個適當水平的SLD保護，勢在必行的是有一個適當設計的電路和溫度控制器。Superlum公司提供PILOT驅動器容許在高水平的穩定性和保護上運轉本公司生產的所有類型的冷卻的SLD模塊。
緊湊式底座對所有類型的模塊( DIL, BUT 和 TOW)都有效。光纖耦合模塊嫰夠很容易地由客戶在底座上替換-沒有焊接要求。用TOW1和TOW2封裝組建的和用TOW底座安裝的自由空間輸出SLD模塊不能由客戶更換。 專業設計的9V直流驅動控制器能夠確保SLD模塊有穩定的光功率輸出，同時采用了多種措施以保護電流對SLD光源器件可能造成的損壞。
Pilot4-DC是經過用戶大量使用的，證實的理想驅動控制器，是我們推薦的SLD模塊驅動器。
特征：
• driving of all types of cooled modules of SUPERLUM,
• stabilization of SLD temperature at any value within range of +10 °C to +40 °C, with indication of the set temperature,
• stabilization of SLD direct current at any value from 0 mA to 400 mA with indication of the set current value. Higher current ranges are available on request.
• High level of SLD protection against overloading
• Low noise
Accessories:
- Mounts for modules (DIL, BUT, TOW)
- Connecting cables
- External low pass filter
Optional: remote control of SLD status and its on/off by external logic
Stability and noise
All PILOT controllers allow excellent stability of SLD modules. Typical short-term (15 min, 22±0.1 °C ambient) and long-term (3 h, 22±0,5 °C) stability of SLD modules driven by PILOTs is 500 ppm and 3000 ppm, correspondently.
No any excess noise to SLD intensity noise is added by PILOT-4 in frequency range 0,05-10 MHz; external LPF allows no excess noise starting 1 KHz frequency.
|
Current source, constant current mode |
SLD protection section |
|
SLD current range* |
0...400mA |
|
|
|
SLD voltage, maximum |
3V |
SLD current limit range* |
5...400mA |
|
Set resolution ** |
0,1mA |
Set resolution** |
0,1mA |
|
Accuracy (50-400mA) |
0,5mA |
Accuracy (50-400mA) |
1mA |
|
|
|
|
|
|
TEC controller section |
PD monitor section |
|
Thermistor range |
6,000 ...19.999kOhm |
|
|
|
Stabilization T range*** |
10-40°C |
PD monitor reverse voltage |
5 V |
|
Accuracy |
0,1°C |
PD monitor current range |
0.....20mA |
|
Maximum TEC current |
1200mA |
Display resolution |
0.001mA |
|
Maximum TEC voltage |
5,0V |
|
|
* - up to 500 mA upon request
** - corresponds to LCD resolution
***- it is considered that 10K3CG2 of BetaTherm Ltd. Thermistors are used in SLD modules
|
Supply voltage |
9,0V±5% |
|
Supply voltage pulsations |
50 - 240 Hz 150 mV max. |
|
Supply voltage pulsations |
> 240 Hz 1 mV max. |
|
Maximum supply current |
2,0 A |
|
Cable connectors |
9 pin D-SUB |
|
9 V DC connectors |
two 4 mm 'banana' type |
|
Operating temperature |
0...+40 °C |
|
Weight |
0.7 kG |
|
