OG脈沖選擇器 OG Pulse Pickers
特點
–適用波段:250-2100nm
-適用幅度可達12kV
–適用超速脈沖延遲
-超速脈沖持續時間從3到1250ns
-快速啟動可降至1ns或者更低
-單發可達100kHz采集率
-低抖動<200ps
-同步光學調整或者通過外部TTL信號調制
-同步光學調整通過光纖進入內嵌探測器
-內部/外部控制
-通過外部或內部信號運行突發模式
–一個控制裝置可以控制三個普克爾盒
-內置雙分頻器
-四個獨立延遲通道0…4us(可根據要求增加到800us)
-1ms全通道額外群延時
-所有內部信號控制單元都是可編程輸出的
-USB控制和LabView驅動
應用
-從飛秒或皮秒脈沖中進行單個或多個的脈沖選擇
-減少功率放大的脈沖重復率
-脈沖選擇對比增加
-注入/排出脈沖輸入/輸出再生放大器
-同步和觸發外部設備
基礎OGB/1系統包括:
·OG脈沖選擇器光學探頭可超快驅動
·通過連接USB同步控制19”供電模塊
·兩個格蘭棱鏡支架和支柱
·1.5米光學光纖光纜連接內置探測器
OG 脈沖選擇系統額外規格
|
OG8/1
OG12/1 |
OG8/10
OG12/10 |
OG8/25 |
OG8/50 |
OG55/1 |
OG88/1 |
OG8/1-F |
電池電壓,可調節 |
5…8kV
7…12kV |
5…8kV |
3…5kV |
5…8kV |
5…8kV |
ARC |
750-850nm for OGB and 1000-1100nm for OG12/OG55(other ranges and wideband on request) |
EO crystal |
DKDP |
BBO |
DKDP |
通光孔徑 |
5mm standard(up to 20 mm on request) |
3.5 mm |
5 mm |
超快脈沖寬度占最大振幅寬度的10% |
<10 na, bell-shaped |
12.1250ns adjustable,squareshaped |
<3ns |
上升時間 |
<4 ns |
<10 ns |
<700 ps |
下降時間 |
<4 ns |
<10 ns |
<2 ns |
輸出重復頻率 |
0…1 kHz |
0…10 kHz |
0…25 kHz |
0…50 kHz |
0…1 kHz |
0…1 kHz |
高壓驅動響應時間 |
<180 ns(fixed delay between the trigger pulse and the high voltage pulse) |
光學標準傳輸系統 |
Half-wave scheme >85%; quarter-wave scheme >80%;
Pockels cell transmission without polarizers >98% |
穩定性(抖動) |
<200 ps |
啟動裝置 |
Internal or external (see specs for Control and Supply Unit) |
同步射頻信號 |
Optical (supplied to built-in fiber-coupled photodetector) or electric |
輸入光重復頻率 |
2…150 MHz ad 1 Hz…2 MHz |
可調延遲 |
0…4μs(0…800 μs on request) |
對比率 |
>103:1 |
外部水箱調整 |
no |
yes |
no |
yes |
No |
1) The Pockels cell voltage defines the wavelength on which the system operates. Thus in a simple half-wave scheme the voltage amplitude in kV roughly corresponds to wavelength in hundreds of nm, i.e. if you require
the system for 800 nm you are looking for a ~8 kV unit, 1064 nm – 10 kV etc. ARC can be then done according to your request.
2) The optical train rep. rate is first optionally divided by a prescaler of either 1/16/256/4096 and then by a compulsory divisor of an integer from range of 2 to 65535 to get the desired output frequency. The unit also
provides burst and single-shot modes. There is also an additional external electric TTL trigger connection available for control of output pulse frequency. See CU specs for more details.
3) Proper operation with input train rep. rate 1 Hz…2 MHz is only available with triggering by external signal. The external trigger signal must lead the optical pulse by 0.25-3 μs and must be strictly locked to the optical
train with jitter less than 200 ps
4) Value of dissipated thermal power for OG8/25 and OG88/1 is approximately 25 W, for OG8/50 around 50 W |
Optional units:可選單位:
OG8(12)/1(10)-2 :2-channel system driving single Pockels cell by two HV pulses. Perfect for injection/ejection in solid-state fs amplifiers.
OG8/100 :Up to 100 kHz repetition rate, external water cooling is needed (the value of dissipated thermal power at 100 kHz is approximately 80 W).
OG55/20 :Up to 20 kHz repetition rate, external water cooling is needed (the value of dissipated thermal power at 20 kHz is approximately 40 W).
|